2025-07-01

Using Powerwall 3 Ramps to Unload Powerwall 3

Safety and PPE
  • Cut-resistant gloves (ANSI Cut Level 3 or EN 388 Level C)
  • Safety boots
Required Parts and Tools
  • Powerwall 3 Ramps (Tesla P/N 1913330-xx-y)
  • (2) Pry tools
    • Channel strut or 1" EMT conduit, cut at 16 - 24" length

  1. Clamp the ramps to the Powerwall 3 packaging:
    • For ramps with part number xxxxxxx-00-A through xxxxxxx-00-G, use the pin latch to clamp the right and left collapsing ramps to the Powerwall 3 packaging:
      1. Remove the pin.
      2. Attach the clamp to the Powerwall 3 packaging.
      3. Insert the pin, verifying that it comes out the other side of the clamp.
      4. Perform a pull test to ensure the ramp is locked in place.
    • For ramps with part number xxxxxxx-00-H and later, use the latch lock to clamp the right and left collapsing ramps to the Powerwall 3 packaging:
      1. Press the tab to unlock the clamp.
      2. Attach the clamp to the Powerwall 3 packaging.
      3. Perform a pull test to ensure the ramp is locked in place.
  2. Use the pull pins to extend both ramps until they are between 0 - 5 degree incline on the integrated level on the sides of the ramps.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure the latches are locked in and secured.
  3. Release the lateral support latch from the right-hand side collapsing ramp.
  4. Attach the lateral support latch to the left-hand side collapsing ramp.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Ensure that the support is securely attach to the left-hand side ramp
  5. As a secondary safety measure, place sandbags at the bottom of the rails.
  6. With two operators using pry tools, leverage the Powerwall 3 packaging up and off of the stack, and position it onto the ramp.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pry tools can be anything similar to a channel strut or 1" EMT, 16-24 inches in length.
    Informational PurposesAn informational icon, calling your attention
    Note
    You will need to pry two times to position the Powerwall 3 packaging onto the ramp.
  7. With the pry tools, position the Powerwall 3 crate so that the middle feet of the crate are sticking out roughly 1 inch from the packaging below it.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Serious injury may occur if the top crate does not have the minimum clearance from the packaging below it.
  8. With two operators, tilt and move the Powerwall 3 packaging until it is fully on the ramp.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Only grab the top of the packaging. Do not attempt to lift the Powerwall 3 packaging from beneath.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Ensure the Powerwall 3 packaging is securely sitting on the ramps before moving to next step.
  9. Push the Powerwall 3 packaging down the ramps.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Use extra caution when the condition is wet, snowy, or winding.
  10. Remove sandbags.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Do not step in front of the Powerwall's path to remove the sandbags.
  11. Slide Powerwall to the bottom of the ramp.
  12. Follow the Powerwall Dolly User Manual instructions to remove the Powerwall from the packaging.