Appendix J: Revision History


Revision	Date	Description
1.23	April 3, 2026	Updated Gateway 3 Service Parts, Orderable Parts, and Accessories with Gateway 3 communication connector part number Updated Powerwall 3 Tools, Service Parts, and Orderable Parts and STEP 7: Install Clamp-on Ferrite Cores / Metal PV Shield with clarification on which Powerwall 3 accessory bag is included with Powerwall 3 depending on its part number Added Fastener Quantity and Stacking Table to mounting appendix Updated support email to ResiDesignReview@tesla.com in Electrical Equipment Sizing and Overcurrent Protection
1.22	January 21, 2026	Updated Tesla Components to include Tesla Remote Energy Meter kit part number (the kit includes the Tesla Remote Energy Meter and is the part number that can be ordered) Updated Load Shedding Feature to clarify that the load shedding feature can only be used to control loads, and is not approved for AC-coupled solar
1.21	December 18, 2025	Updated Choose Powerwall Cable Entry to reflect that a punch and die set must be used if expanding Powerwall 3 knockouts Updated Test PV Strings with MCIs to clarify insulation resistance testing procedure
1.20	September 5, 2025	Updated Site Requirements and Pre-Installation Guidance and STEP 5: Make Powerwall 3 AC Circuit Connections with additional guidance when using Eaton branch breakers for Powerwall
1.19	July 25, 2025	Updated Required Supplies and Make PV Power Connections to reflect that solid core or single core wire cannot be used for PV connections
1.18	July 11, 2025	Removed Connect CAN / 12V Circuits via CAT5 or CAT6 Ethernet Wiring (no longer supported at this time)
1.17	June 19, 2025	Updated Commission the System After Powerwall and Solar Installation and Commission the System Ahead of Solar Installation to clarify which QR code must be scanned to connect to Powerwall 3 Added Connect CAN / 12V Circuits via CAT5 or CAT6 Ethernet Wiring Updated Appendix G: Installing Multiple Powerwall 3 Units and/or Expansion Units to reflect that Leader and Follower Powerwall 3 units cannot be connected using a Powerwall 3 Expansion Harness
1.16	May 21, 2025	Updated several topics to include Powerwall 3 units with part numbers 1707000-11-L and higher and 1707000-21-L and higher Updated STEP 3: Wall-Mount Powerwall 3 Using Wall Bracket to reflect that only the upper set of Powerwall 3 cleats is fully seated on the bracket flanges Updated Load Shedding Feature with option to install an override switch Updated Electrical Equipment Sizing and Overcurrent Protection to remove impedance requirements for 1-2 units (impedance testing not required in this case)
1.15	April 22, 2025	Added note to Site Requirements and Pre-Installation Guidance that fully off-grid sites are not supported Updated Mount Gateway 3 to include step to punch out mounting hole knockouts (where required) and fastener requirements for soft wall substrates Added note to STEP 11: Turn On and Commission the System on methods to enable grid export when allowed by utility Added Load Shedding Feature
1.14	March 20, 2025	Added minimum room size to Choose a Location that Meets Powerwall 3 Clearance Requirements
1.13	March 14, 2025	Added Electrical Equipment Sizing and Overcurrent Protection for multi-Powerwall systems Updated Install Stacked Expansion Units to reflect that the shims should be installed on the bracket before mounting the bracket to the rear Expansion unit
1.12	January 24, 2025	Added Test PV Strings with MCIs Updated STEP 11: Turn On and Commission the System with reminder to install MCIs and connect / test PV strings before turning Powerwall 3 ON Updated Powerwall 3 Wall Bracket Anchoring Details for Wall-mounting or Ground-mounting on Approved Foundation to reflect that the bracket fasteners should be installed on the outside edges of the bracket slots for greater stability when anchoring to concrete, brick, or channel strut Updated Install Expansion Units with Powerwall 3 with guidance for painting the Expansion Harness Updated Wall Mount an Expansion Unit with strapping guidance when using the 0.5 Expansion Harness in a wall-mounted configuration
1.11	November 21, 2024	Updated Powerwall 3 Specifications and Install MPPT Jumpers (Optional) to reflect updated Powerwall 3 I_MP of 15 A and I_SC of 19 A Updated Install Mid-Circuit Interrupters in PV Array with "Always 4" rule option for number of required MCI-2s Updated Channel Strut section and made general update to attach fasteners on outer edge of bracket slots in Powerwall 3 Wall Bracket Anchoring Details for Wall-mounting or Ground-mounting on Approved Foundation Added Powerwall 3 Wall Bracket Anchoring Details for Stacked Configurations Updated Concrete Pad Details for Ground-mounting Powerwall 3 on Pre-Cast Concrete Pad an Existing Structural Wall to reflect pre-cast concrete pad Added partial home backup example to Gateway 3 Wiring Diagrams
1.10	October 24, 2024	Updated Powerwall 3 Specifications, Required Supplies, and STEP 5: Make Powerwall 3 AC Circuit Connections to reflect that Powerwall 3 can be configured to have an off-grid maximum continuous discharge power of 15.4 kW if installed with an 80A breaker and appropriately sized conductors Updated Mid Circuit Interrupter Specifications (P/N MCI-2) PV Rapid Shutdown Equipment (PVRSE) to include MCI-2 High Current current ratings
1.9	October 9, 2024	Updated Install Mid-Circuit Interrupters in PV Array to clarify that MCI(s) must be installed on any PV system connected to Powerwall 3
1.8	September 9, 2024	Corrected maximum combined harness length when Expansion units are connected on both sides of Leader Powerwall 3 in Wall Mount an Expansion Unit Corrected allowable wire range for Ground terminals (metric only, corrected 2.5 mm² to 4 mm²) in Powerwall 3 AC and PV Wiring
1.7	September 17, 2024	Updated STEP 9: Install Energy Metering for the System to reflect availability of Tesla Remote Meter Added Powerwall 3 Center of Mass and updated Powerwall 3 Wall Bracket Anchoring Details for Wall-mounting or Ground-mounting on Approved Foundation with additional details on wall bracket anchoring requirements depending on mounting configuration Updated Install Expansion Units with Powerwall 3 to reflect stacked mounting configuration option and added specific stacking instructions in Install Stacked Expansion Units
1.6	September 4, 2024	Added Powerwall 3 Expansion Specifications and Install Stacked Expansion Units
1.5	August 13, 2024	Updated Mechanical Specifications to reflect that the Powerwall 3 height is 43.5 in (1105 mm) when the glass front cover is installed Updated In the Powerwall 3 Box and STEP 7: Install Clamp-on Ferrite Cores / Metal PV Shield to reflect that only (2) ferrite cores are required for Powerwall 3 units with Tesla P/N 1707000-11-L or 1707000-21-L Updated Close Wiring Compartments to reflect that front cover fasteners can be reused Updated General Anchoring Notes to reflect that Powerwall 3 cannot be mounted to a chimney
1.4	July 24, 2024	Updated Powerwall 3 Specifications to reflect Powerwall 3 power / current output can be limited; added guidance for locating the part number and serial number on a Powerwall 3 unit Updated Mid Circuit Interrupter Specifications (P/N MCI-1) PV Rapid Shutdown Equipment (PVRSE), Mid Circuit Interrupter Specifications (P/N MCI-2) PV Rapid Shutdown Equipment (PVRSE), and Install Mid-Circuit Interrupters in PV Array with link to UL 3741 Application Addendum for complete list of systems that have been certified to UL 3741 when installed together with Powerwall 3 and Tesla MCI Updated In the Powerwall 3 Box and Powerwall 3 Tools, Service Parts, and Orderable Parts to reflect that Powerwall 3 units with part number 1707000-11-L or 1707000-21-L ship with a different set of MPPT jumpers than all other Powerwall 3 units Updated Required Supplies to reflect that Powerwall 3 units with part number 1707000-11-L or 1707000-21-L can be installed with metallic or non-metallic conduit Updated Make PV Power Connections and Install MPPT Jumpers (Optional) with new PV wiring diagrams and instructions for Powerwall 3 units with part number 1707000-11-L or 1707000-21-L Updated STEP 5: Make Powerwall 3 AC Circuit Connections with instructions to choose Powerwall 3 breaker size based on configured power output, as well as to mark configured power output on the Powerwall 3 product label
1.3	July 1, 2024	Updated Maximum Output Fault Current and added Maximum Short-Circuit Current Rating in Powerwall 3 Specifications Added Maximum Disconnect Voltage to Mid Circuit Interrupter Specifications (P/N MCI-1) PV Rapid Shutdown Equipment (PVRSE) and Mid Circuit Interrupter Specifications (P/N MCI-2) PV Rapid Shutdown Equipment (PVRSE) Updated Required Supplies to reflect that minimum NEMA 4 (IPX5) fittings are only required when installing Powerwall 3 outdoors Updated Install Mid-Circuit Interrupters in PV Array with warning that where it is allowable to install only (1) MCI per string, MCI-1 must be used Updated STEP 5: Make Powerwall 3 AC Circuit Connections to reflect Fast Acting fuse requirements if using a 60A fuse rather than a circuit breaker for Powerwall 3 overcurrent protection
1.2	May 29, 2024	Updated Powerwall 3 Specifications and STEP 5: Make Powerwall 3 AC Circuit Connections to reflect fuse requirements if using a 60A fuse rather than a circuit breaker for Powerwall 3 overcurrent protection
1.1	May 8, 2024	Corrected maximum branch breaker rating in Acceptable Circuit Breakers
1.0	April 25, 2024	Initial publication